etd AT Indian Institute of Science >
Division of Mechanical Sciences >
Materials Engineering (formely known as Metallurgy) (materials) >
Please use this identifier to cite or link to this item:
|Title: ||Magnesium Matrix-Nano Ceramic Composites By In-situ Pyrolysis Of Organic Precursors In A Liquid Melt|
|Authors: ||Sudarshan, *|
|Advisors: ||Surappa, M K|
|Keywords: ||Ceramic Composites|
Magnesium Ceramic Composites
Liquid Melt Composites
Organic Polymer Precursors
Metal Matrix Composites (MMCs)
Magnesium Matrix-Nano Ceramic Composites
Magnesium Matrix Composites - Fabrication
Nanoceramic Metal Matrix Composites
|Submitted Date: ||Sep-2010|
|Series/Report no.: ||G24456|
|Abstract: ||In this thesis, a novel in-situ method for incorporating nanoscale ceramic particles into metal has been developed. The ceramic phase is introduced as an organic-polymer precursor that pyrolyzes in-situ to produce a ceramic phase within the metal melt. The environment used to shield the melt from burning also protects the organic precursor from oxidation. The evolution of volatiles (predominantly hydrogen) as well as the mechanical stirring causes the polymer particles to fragment into nanoscale dispersions of a ceramic phase. These “Polymer-based In-situ Process-Metal Matrix Composites” (PIP-MMCs) are likely to have great generality, because many different kinds of organic precursors are commercially available, for producing oxides, carbides, nitrides, and borides. Also, the process would permit the addition of large volume fractions of a ceramic phase, enabling nanostructural design, and production of MMCs with a wide range of mechanical properties, meant especially for high temperature applications. An important and noteworthy feature of the present process, which distinguishes it from other methods, is that all the constituents of the ceramic phase are built into the organic molecules of the precursor (e.g., polysilazanes contain silicon, carbon, and nitrogen); therefore, a reaction between the polymer and the host metal is not required to produce the dispersion of the refractory phase.
The polymer precursor powder, with a mean particle size of 31.5 µm, was added equivalent to 5 and 10 weight % of the melt (pure magnesium) by a liquid metal stir-casting technique. SEM and OM microstructural observations show that in the cast structure the pyrolysis products are present in the dendrite boundary region in the form of rod/platelets having a thickness of 100 to 200 nm. After extrusion the particles are broken down into fine particles, having a size that is comparable to the thickness of the platelets, in the 100 to 200 nm range, and are distributed more uniformly. In addition, limited TEM studies revealed the formation of even finer particles of 10-50 nm. X-ray diffraction analysis shows the presence of a small quantity of an intermetallic phase (Mg2Si) in the matrix, which is unintended in this process.
There was a significant improvement in mechanical properties of the PIP-MMCs compared to the pure Mg. These composites showed higher macro-and micro-hardness. The composite exhibited better compressive strength at both room temperature and at elevated temperatures. The increase in the density of PIP-composites is less than 1% of Mg. Five weight percent of the precursor produced a two-fold increase in the room-temperature yield strength and reduced the steady state creep rate at 723 K by one to two orders of magnitude. PIP-MMCs showed higher damping capacity and modulus compared to pure Mg, with the damping capacity increasing by about 1.6 times and the dynamic modulus by 11%-16%. PIP-composites showed an increase in the sliding wear resistance by more than 25% compared to pure Mg.|
|Abstract file URL: ||http://etd.ncsi.iisc.ernet.in/abstracts/2669/G24456-Abs.pdf|
|Appears in Collections:||Materials Engineering (formely known as Metallurgy) (materials)|
Items in etd@IISc are protected by copyright, with all rights reserved, unless otherwise indicated.